Punch in and out of audio recordings in Logic Pro for Mac
Punch recording is a technique you can use to overwrite a portion of a previously recorded track, during playback, without touching any of the recording before or after that portion. You punch in to interrupt playback and make the recording, then punch out to return to playback mode. You can choose between two punch recording modes: Quick Punch-In mode and Autopunch mode.
When Enable Complete Features is selected in Logic Pro > Settings > Advanced, Punch recording is available.
Quick Punch-In mode
A useful and common recording practice is to switch in and out of recording mode while listening to the previously recorded material, sometimes referred to as “punching in on the fly.” This helps you fix mistakes or create alternate takes for a particular section. To ensure the transition between playing and recording occurs without any audible gaps, you must turn on Quick Punch-In mode.
When Quick Punch-In mode is on, recording occurs in the background from the moment you start playback. This means there needs to be twice the number of available channel strips than the number enabled for recording. A dialog appears if you exceed the number of channel strips needed.
Important: It is recommended that you leave Quick Punch-In mode turned on (which it is, by default). You only need to turn it off if you’re recording more than the number of channel strips available (in a new project that’s more than 1,000 tracks), or if your hard disk is unable to accommodate recording a large number of tracks. To turn it off, choose Record > Allow Quick Punch-In, or Control-click the Record button, then choose Allow Quick Punch-In from the shortcut menu.
Autopunch mode
Autopunch describes the use of predefined punch-in and punch-out points to start and stop recording. One advantage is that you can concentrate on your playing, rather than on controlling the software. Another advantage is that you can set the starting and stopping of recordings far more precisely than is possible if “punching in on the fly.”
Note: Only record-enabled tracks are affected by punch recording.
When it comes to judging punch-in and punch-out points during punch recording, you should turn on auto input monitoring (which it is, by default). This setting allows you to hear the input signal only during the actual recording; before and afterward you’ll hear the previously recorded audio on the track. If auto input monitoring is turned off, you can always hear the input signal.
In Logic Pro, do one of the following:
Choose Record > Auto Input Monitoring.
Control-click the Record button in the control bar, then choose Auto Input Monitoring from the shortcut menu.
In Logic Pro, turn on Quick Punch-In mode by doing one of the following:
Choose Record > Allow Quick Punch-In.
Control-click the Record button in the control bar, then choose Allow Quick Punch-In from the shortcut menu.
Click the Play button in the control bar, then use the Record Toggle key command at the point where you want to start recording.
Audio recording starts immediately.
Click the Stop button in the control bar, or use the Record Toggle key command a second time to stop recording. If an audio region already existed where you recorded on the fly, a new audio region with your recording replaces the previously recorded region.
If you use the Record Toggle key command a second time, recording ends, but playback continues.
Note: You can also use the Record Toggle key command when not in Quick Punch-In mode. However, this causes a delay when you switch between playback and record modes, accompanied by a dropout of all audio tracks.
In Logic Pro, turn on Autopunch mode by doing one of the following:
Click the Autopunch button in the control bar.
Note: You can add the Autopunch button by customizing the control bar. For information, see Customize the control bar.
The autopunch area is indicated by a red stripe in the middle third of the ruler, with the left and right autopunch locators serving as punch-in and punch-out points.
Set the autopunch area by doing one of the following:
Drag the Punch In and Punch Out locators in the ruler.
Drag vertically in the autopunch locator fields in the control bar.
Drag the cycle area into the autopunch area to quickly match the autopunch area to the cycle range.
Use the Marquee tool to select the autopunch area on the track.
Note: To use the Marquee tool in this way, Control-click the Autopunch button in the control bar, and make sure Marquee Selection Engages Autopunch Recording is selected in the shortcut menu.
Place the playhead at any position before the punch-in point.
Click the Record button in the control bar (or press R) to start recording.
Click the Stop button in the control bar (or press the Space bar) to stop recording.
A region that matches the length of the autopunch area is created. Any audio input received before the punch-in or after the punch-out point streams through Logic Pro as usual, but is not recorded.
If you want to improve a difficult part of a certain passage, you can use a combination of the Cycle and Autopunch functions. Cycle mode recording allows you to practice as many times as you like before performing the final take. On each cycle pass, only events or audio that falls within the area defined by the autopunch locators is recorded. This lets you make use of the preceding song section to “get into the groove.”
You can set a predefined punch-in point using a marquee line so that you can record from the punch-in point to the end of your project or until you stop recording.
In Logic Pro, Control-click the Autopunch button in the control bar.
Note: You can add the Autopunch button by customizing the control bar. For information, see Customize the control bar.
Choose Marquee Line Engages Autopunch Recording from the shortcut menu.
Use the Marquee tool to click the point in the track where you want to set the punch-in.
The autopunch area is indicated by a red stripe in the middle third of the ruler and runs to the end of your project.
When Enable Complete Features is selected in Logic Pro > Settings > Advanced, Punch recording is available.
in the control bar, then choose Auto Input Monitoring from the shortcut menu.
in the control bar, then use the Record Toggle 
in the control bar, or use the Record Toggle key command a second time to stop recording. If an audio 
in the control bar.