MacBook Air (15-inch, M2, 2023) Display

Before You Begin

Remove the following parts before you begin:

Tools

Adjustable torque driver (10–34 Ncm)
Adjustable torque driver (0.3–1.2 Nm)
ESD-safe tweezers
Nylon probe (black stick)
Torque driver (blue, 0.65 kgf cm)
Torx Plus 3IP 44 mm half-moon bit
Torx Plus 3IP bit
Torx Plus 8IP bit

Caution

This procedure requires System Configuration. After you’ve completed all removal and reassembly steps, learn how to initiate the System Configuration process.
If you’re installing a replacement display, you must also install a replacement lid angle sensor.

Removal

Use the 10–34 Ncm adjustable torque driver and 3IP bit to remove the two 3IP screws (923-09230) from the display flex cables cowling.
Use ESD-safe tweezers to gently peel back the foam from both ends of the display connectors cowling to access the two middle screws.
- Important: Don't remove the foam from the cowling.
Use the blue torque driver and 3IP half-moon bit to remove the four 3IP screws (923-08925) from the display connectors cowling.
Remove the display connectors cowling and save it aside for reassembly.
Use a black stick to lift the ends of the two display flex cables (1) and lid angle sensor flex cable (2) off the connectors.
Open the display. Then place the computer on the edge of the table with the display hanging down.
- Caution: Ensure that the display flex cables don't get caught on the logic board as you open the display.
Use the 0.3–1.2 Nm adjustable torque driver and 8IP bit to remove the eight 8IP screws (923-09561) from the display hinges.
Tilt up the display fully.
- Caution: Ensure that the lid angle sensor flex cable doesn’t get caught on the top case (1) as you lift the display off the top case (2).

Reassembly

Position the display on the top case as shown.
- Caution: Ensure that the lid angle sensor flex cable (1) and display flex cables (2) don’t get caught on the top case or logic board.
Use the 0.3–1.2 Nm adjustable torque driver and 8IP bit to partially reinstall eight 8IP screws (923-09561) into the display hinges.
Lift the top case off the table to close the display beneath it. Ensure that the display is aligned with the top case.
Set the torque value on the 0.3–1.2 Nm adjustable torque driver to 0.75 Nm. Use the adjustable torque driver and 8IP bit to fully reinstall the eight 8IP screws in the order shown.
Press the ends of the two display flex cables to the connectors on the logic board.
- Important
  - If you're installing a replacement display, install a replacement lid angle sensor. Then reinstall the remaining parts to complete reassembly.
  - If you're reinstalling the existing display, continue to step 6.
Press the end of the lid angle sensor flex cable to the connector on the audio board.
Position the display connectors cowling over the ends of the display flex cables.
Use the blue torque driver and 3IP half-moon bit to reinstall two 3IP screws (923-08925) into the outer ends of the display connectors cowling (1).
Use ESD-safe tweezers to peel back the foam near the ends of the display connectors cowling to access the middle screw holes.
Use the blue torque driver and 3IP half-moon bit to reinstall two 3IP screws (923-08925) (2) into the middle of the display connectors cowling. Then gently press the foam over both screws.
Set the torque value on the 10–34 Ncm adjustable torque driver to 11.5 Ncm. Use the adjustable torque driver and 3IP bit to reinstall the two 3IP screws (923-09230) into the display flex cables cowling.