Languages

Archived - AirPort: Turning On Access Control

You can use the MAC Access Control Table in the AirPort Admin Utility to provide additional security for an AirPort Base Station.
This article has been archived and is no longer updated by Apple.
Once you enter the first MAC address, Access Control becomes activated, there is no on/off switch. If you do not enter anything here, all clients will be permitted access. The number of addresses that you can add varies depending on which base station you have. By model:
  • AirPort Base Station (Graphite): 497
  • AirPort Base Station (Dual Ethernet): 300
  • AirPort Extreme Base Station: 500
  • AirPort Express: 25

Note: When you enter information in the description field, this decreases the total number of possible entries. For example, this may decrease to as low as 150 on the AirPort Base Station (Dual Ethernet).

To set up Mac Access Control follow the steps below:

1. In the Access Control tab for the base station, click Add as shown in Figure 1.



Figure 1 Access Control Tab

Note: The window shown in Figure 3 states that "Access to the AirPort network will be restricted to the clients listed here. If nothing is listed, all clients are permitted upon correctly entering the password." This assumes that WEP encryption has been enabled. If it has not, then no password will be required.

2. The Add Client window opens and prompts you for the AirPort ID and Description. Click OK after entering the appropriate information.

The Description entry is optional. However, if you don't enter one, the Access Control table only lists the numeric AirPort ID which makes it extremely difficult to associate it with a particular Client.

The AirPort ID is the same as the MAC Address. The MAC Address can be found on the AirPort card under the serial number. If you already have the card installed in your computer, use Apple System Profiler or the AirPort application to obtain the Mac (hardware) Address.



Figure 2 AirPort Card Showing AirPort ID



Figure 3 Apple System Profiler Window

3. The Access Control Table shows the AirPort ID and Description entered in the previous step.

4. You can enter additional clients to the table by clicking Add and providing the required information. A more complete Access Control Table with five entries is shown in Figure 4.



Figure 4 Access Control Tab

This particular AirPort Base Station (Ebbetts Field) only permits access to the network(s) (Ethernet, DSL, ISP, or cable modem) connected to the base station by the five Clients listed. In this example, the correct network password is also required.

Should an unauthorized client learn the password for this wireless network, they would still be able to associate with the base station and communicate with its associated Clients. However, because their AirPort ID is not in the Access Control Table, they would not be able to access the Ethernet network or dial-out through the Base Station.

Note: For AirPort Base Stations (Graphite) only, even with Access Control on, a client whose MAC address is not entered into the table can still use the control strip to select the network. The client can connect to the Base Station, but not access the Ethernet network or the analog connection. (The LED indicators show up in the control strip and the name gets a bullet next to it in list.)

For wireless clients not in the Access Control Table, file sharing access will still be available via TCP/IP and AppleTalk. Access Control offers little protection to the wireless clients that are not following normal security procedures.

5. When you finish making entries to the Access Control table, click Update to save the changes.

6. After clicking Update, the Base Station must be reset to complete the update. Click OK when the following window appears:



Figure 5 Base Station Reset Dialog Box

Note: Wireless Internet access requires an AirPort Card, AirPort Base Station, and an Internet service provider, for which fees may apply. Some ISPs are not compatible with AirPort. America Online (AOL) works with AirPort software version 2.0 or later. For more information on AOL compatibility, see technical document 106591: "AirPort: How to Use with AOL." Range may vary with site conditions.

Last Modified: Feb 20, 2012
Print this page
  • Last Modified: Feb 20, 2012
  • Article: TA25976
  • Views:

    61763
  • Rating:
    • 44.0

    (17 Responses)

Additional Product Support Information