iPhone 16 Pro Battery

Before You Begin

Warning

• Read Battery Safety and follow workspace and battery handling guidelines before you begin.

• A battery should be replaced only by individual technicians with the knowledge and experience to repair electronic devices. Improper battery replacement, improper handling of parts, or failure to follow the provided instructions could result in fire, injury, data loss, or damage to the device, parts, or other property.

Important

If you replace this part, it's recommended to run Repair Assistant in order to finish the repair. Repair Assistant will be available on the device after you’ve completed all reassembly steps.

Removal

1. Use ESD-safe tweezers to remove three battery adhesive strips.

   • Grasp the battery adhesive tab. Gently peel the adhesive tab away from the battery.

   • Warning: Don’t scrape or puncture the battery with the tweezers.

   • Twist the tab around the tweezers and pull up 1 inch until you see white adhesive strip on the tweezers.

   • Keep the tweezers close and parallel to the battery. Then pull the tweezers toward the top of the iPhone and continue to twist and pull the adhesive until you’ve removed the entire strip. Repeat the process for the second and third adhesive strip.

   • Caution: Don’t pull the adhesive strip against parts or screws.

     

   • Important: If the battery adhesive tab or strip breaks off and you can still see it, attempt to retrieve it with the tweezers. Wrap the tab or strip around the tweezers and continue to twist and pull the adhesive until you've removed the entire strip.

   • Important: If a battery adhesive strip breaks and can't be retrieved, attempt to remove the battery by inserting the flat end of the black stick only into one of the insertion points as shown. Ensure that the black stick is inserted into a point where the battery strip has been fully removed.

     

   • Warning: If you can't remove the battery, stop the repair. You can find a service option at support.apple.com/repair.

2. Remove the battery from the enclosure.

Reassembly

1. Use ethanol wipes or IPA wipes to remove all residual adhesive from the enclosure underneath the battery.

   • Caution: Don't use ethanol wipes or IPA wipes on the outlined area. Ethanol or isopropyl alcohol may damage the polyester film.

   • Warning: Inspect the enclosure for loose or extra screws and small parts, which may damage the battery and cause safety issues.

     

2. Reinstall the Bottom Speaker.

3. Reinstall the Taptic Engine but don't connect the charge port assembly flex cable.

4. Peel the pink release liner from the underside of the replacement battery.

   

   • Don’t remove the protective cover from the top of the battery yet.

5. Hold the battery over the enclosure with the protective cover faceup. Align the right edge of the battery with the logic board and the bottom of the battery with the bottom speaker. Then lower the battery into the enclosure.

   

6. The center of the repair tray has two slots. Position the repair tray and enclosure onto the battery press with the left slot over the pin as shown. Caution: Move the charge port assembly flex cable out of the way of the roller.

   

7. Flip down the lever at the top of the battery press to lower the roller onto the battery. Slide the repair tray back and forth through the battery press three times to adhere the battery to the enclosure.

   

8. Flip up the red lever at the top of the battery press.

9. Position the repair tray and enclosure onto the battery press with the right slot over the pin as shown.

   

10. Repeat steps 7 and 8. Then continue to step 11.

11. Remove the repair tray from the battery press.

12. Hold the edges of the protective cover. Pull the release tabs on the protective cover to remove it from the battery.

    

13. Complete the Taptic Engine reassembly.

Reinstall the following part to complete reassembly:

• Back glass

Warning

Gently shake the iPhone. If the battery feels loose, remove the back glass and the battery. Then complete battery reassembly with another replacement battery.

Important

• A new battery is not charged. After you’ve completed all removal and reassembly steps, charge the device for a few minutes.

• After you’ve completed all reassembly steps, Repair Assistant will be available on the device and is recommended to finish the repair. Learn how to initiate Repair Assistant.